Allen-Bradley Rockwell Automation 1734-AENT Manuel d'utilisateur Page 44
- Page / 158
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Publication 1734-UM011D-EN-P - May 2011
28 Configure the Adapter for Direct Connection in RSLogix 5000 Software
• Add the local 1756-ENBT module to the I/O configuration.
• Add the 1734-AENT adapter as a child of the 1756-ENBT module.
• Add the I/O modules as children of the 1734-AENT adapter.
Add the Local EtherNet/IP Bridge to the I/O Configuration
1. Select the I/O Configuration folder in the project dialog, and click the
right mouse button.
A dialog opens.
2. Click New Module.
IMPORTANT
Click the Help buttons on the configuration dialogs shown
in this section if you need assistance in selecting and setting
the parameters.
- Catalog Number 1734-AENT 1
- User Manual 1
- Important User Information 2
- ATTENTION 3
- How to Use This Manual 4
- System Components 5
- Where to Find More 6
- Information 6
- Terminology 7
- Preface ix 9
- Table of Contents 11
- xiii 13
- Summary of Changes 15
- About the Adapter 17
- Adapter Replacement 18
- About the Adapter 3 19
- Adapter Features 20
- Hardware/Software 21
- Compatibility 21
- What the Adapter Does 21
- Use of the Common 21
- Industrial Protocol (CIP) 21
- Understand the 22
- Producer/Consumer Model 22
- Specify the Requested 22
- Packet Interval (RPI) 22
- Support of Rack-optimized 23
- Before You Begin 24
- Install the Adapter 25
- Mount the Adapter on a DIN 26
- Rail Before Installing 26
- Mount or Replace 27
- Existing System 27
- Wire Your Adapter 28
- Mounting Dimensions 29
- 14 Install the Adapter 30
- What This Chapter Contains 31
- Configuration 32
- Requirements 32
- IP Address 33
- Gateway Address 33
- Subnet Mask 34
- Set the Network Address 35
- Use the Rockwell 36
- BootP/DHCP Utility 36
- Save the Relation List 38
- Use DHCP Software to 39
- Configure Your Adapter 39
- Set Up the Hardware 41
- Create the Example 42
- Application 42
- Configure the I/O 43
- Name Local_ENB 46
- IP Address 10.88.70.4 46
- Revision 3.1 46
- Add the Relay Output Module 49
- The New Module dialog opens 50
- Name POINT_Relay_Output 51
- Add the Digital Output Module 52
- Name POINT_Digital_Output 53
- Edit the Controller Tags 54
- Create the Ladder Program 55
- Download the Program to 55
- Verify the Module Chassis 57
- 8. Click OK to continue 58
- Configure the Adapter with 59
- Fixed IP Address 59
- Recover From an 60
- Overloaded Adapter 60
- Software 61
- Configure the I/O Modules 64
- Revision 1.1 66
- Connection 69
- 5. Choose Connection 70
- Verify the Module 75
- Chassis Size 75
- 3. Select Properties 76
- 4. Click the Connection tab 76
- → Save to save the project 77
- Access Module Data 78
- LED Status Indicators 79
- Adapter Web Pages 83
- Work with the Diagnostics 85
- 70 Adapter Web Pages 86
- Use the Network Settings Page 87
- 72 Adapter Web Pages 88
- Adapter Web Pages 73 89
- Use the I/O Connections Page 90
- Adapter Web Pages 75 91
- Work with the 92
- Configuration Pages 92
- Use the Identity Page 93
- 78 Adapter Web Pages 94
- Adapter Web Pages 79 95
- Work with the Browse 96
- Chassis Page 96
- •Module Revision 99
- • Serial Number 99
- • Status 99
- 84 Adapter Web Pages 100
- Communication Driver 101
- Configure the AB_ETH/IP 102
- Controller Tag Reference 105
- Valid Number Ranges for 106
- RSLogix 5000 Data Types 106
- Digital 2 POINT Input 107
- Digital 4 POINT Input 108
- Digital 2 POINT Output – 109
- Without Diagnostic Status 109
- With Over Load and Open 110
- Load Diagnostic Status 110
- With Over Load Diagnostic 111
- Digital 4 POINT Output – 112
- Analog 2 Channel Input 114
- INT 0 0…7,000 (0.00…70.00) 121
- Analog 2 Channel Output 123
- Specialty I/O 127
- Stored Data 131
- Program Fault 131
- Decimal Position 134
- Gate Interval 134
- Program Fault Note 136
- SSI Word Delay Time 138
- Sensor Resolution 138
- Sensor Cycle 138
- Compare 0,1 Value 138
- Present / Latched Data 139
- Quick Start 145
- Configure the Adapter 146
- Enter Adapter Properties 147
- 134 Quick Start 148
- Configure 1734 POINT I/O 149
- Modules 149
- 136 Quick Start 150
- IMPORTANT 151
- Configure an Ethernet 152
- Driver in RSLinx Software 152
- Quick Start 139 153
- 140 Quick Start 154
- 142 Index 156
- Rockwell Automation Support 158
- Documentation Feedback 158
Produits connexes et manuels pour Mise en réseau Allen-Bradley Rockwell Automation 1734-AENT
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels