Allen-Bradley 2-D Manuel d'utilisateur Page 39
- Page / 92
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter
5
Parameters and Programming
Overview of Parameters
This chapter describes both Display and Program parameters. Display parameters
are read only (they cannot be programmed), while Program parameters can be
changed to fit your motor control requirements. You must have a Program Keypad
Module to view or change parameters. The table below describes which parameters
apply to the Preset Speed and Analog Signal Follower models.
Some parameters pertain only to either the Analog Signal Follower or Preset Speed
model, not both.
Review the factory default settings. If your drive is equipped with a Program
Keypad Module, these parameters can be changed to meet your specific application
requirements. The table below provides a list of parameters that are frequently
changed.
Commonly Changed Parameters Table 5.A
Refer to the Programming Example on the next page for instructions.
Parameter Type Analog Signal Follower Model
Parameter Numbers
Preset Speed Model
Parameter Numbers
Display 1 – 19 1 – 15, 17 – 19
Program 30 – 62, 65 – 66, and 69 – 76, 78 – 84 30 – 59 and 61 – 73, 78 – 80
⇐
Indicates that parameter applies only to the Analog Signal Follower Model
⇐
Indicates that parameter applies only to the Preset Speed Model
Parameter Setting Default Setting
P30 - [Accel Time 1] Desired accel time. 10.0 sec
P31 - [Decel Time 1] Desired decel time. 10.0 sec
P33 - [Maximum Frequency] Maximum frequency required. 60 Hz
P34 - [Stop Mode Select] Desired stopping mode. 0
P35 - [Base Frequency] Motor rated nameplate frequency. 60 Hz
P36 - [Base Voltage] Motor rated nameplate voltage. 460V or 230V
P38 - [Boost Select] Desired V/F setting. 2
P42 - [Motor Overload Current] Motor nameplate Full Load Amps (FLA). 115%
P43 - [Current Limit] Desired maximum output current. 150%
P46 - [Input Mode] Desired control method. 0
P47 - [Output Configure] Desired output relay function. 0
P56 - [Reset Functions] Desired drive reset description. 0
P58 - [Internal Frequency] Desired internal frequency. 60.0 Hz
P59 - [Frequency Select] Desired frequency source. 0
P61 – P68 - [Preset Frequency 0-7] Desired preset frequencies. 0-7
P74 – P76 - [Analog Input] Desired analog input functionality. 0, 0.0, 100.0%
- 160 SSC™ 1
- Variable Speed 1
- (Series C) 1
- Important User Information 2
- Series C Summary of Changes 3
- Table of Contents 5
- Getting Started 7
- 160 -AA02 N SF1 P1 8
- 160-AA02NSF1P1 9
- Standard Drive Features 10
- Optional Drive Features 11
- End of Chapter 12
- Installation and Wiring 13
- Power Wiring 14
- Specifications 15
- Terminal Block Wiring 15
- Motor Branch Circuit Analysis 16
- Input Power Conditioning 18
- Motor Cable Types 18
- Reflected Wave Protection 19
- Capacitive Current Coupling 20
- Nm (lb in) 21
- Wiring Diagram Key 22
- 2-12 Installation and Wiring 24
- Installation and Wiring 2-17 29
- Analog Frequency Sources 30
- Preset Frequency Sources 31
- Internal Frequency Source 32
- Program Keypad Module 33
- Key Functions 34
- Program Keypad Module 3-3 35
- Installation 36
- Start-Up 37
- 4-2 Start-Up 38
- Parameters and Programming 39
- Important Reset Actions 40
- Programming Example 40
- Display Group (Read Only) 43
- 0/48 Numeric Value 43
- Program Group Parameters 44
- % [Base Frequency] 45
- % [Base Voltage] 45
- 46 [Input Mode] 47
- 47 [Output Configure] 47
- 48 [Output Threshold] 47
- 49 [PWM Frequency] 48
- 50 [Restart Tries] 48
- 51 [Restart Time] 48
- 52 [DB Enable] 48
- 53 [S-Curve] 49
- 54 [Clear Fault] 49
- 55 [Memory Probe Address] 49
- 56 [Reset Functions] 49
- Preset Speed Model Only 50
- Signal Follower 50
- Model Only 50
- Settings: 52
- 81 [PI Proportional Gain] 53
- 82 [PI Integral Gain] 53
- 83 [PI Process Reference] 53
- 84 [PI Dead Band] 53
- 160 PI Control Setup 54
- Troubleshooting 57
- Problem Corrective Action 59
- 6-4 Troubleshooting 60
- CSA 22.2 62
- Specifications A-3 63
- End of Appendix 64
- Accessories and Dimensions 65
- Accessory Dimensions 66
- Line Filters Figure B.3 67
- MADE IN U.S.A 68
- 29 ➊ 69
- Drive Dimensions 70
- 5.5 (0.22) 72
- Mounting Holes—2 Places 72
- CE Conformity 75
- Shielded Enclosure 76
- Cable Clamps 77
- Motor Cable 77
- Control Wiring TB3 78
- Ground Terminal – PE 78
- CE Conformity C-5 79
- Index-10 90
Produits connexes et manuels pour Lecteurs de codes-barres Allen-Bradley 2-D
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels