Allen-Bradley 2-D Manuel d'utilisateur Page 94
- Page / 172
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Programming
5-25
This group of parameters allows the user to program the frequency source, frequency settings, accel/decel
times and skip frequencies of the drive.
Frequency
Set
[
F
re
q S
e
l
e
c
t
1
]
Parameter # 5 Factory Default “Adapter 1”
[
F
re
q S
e
l
e
c
t
1
]
Parameter Type Read & Write
This parameter is the factory default parameter for
selecting the frequency source that will supply the [Freq
Command] to the drive. [Freq Select 2] or [Preset Freq
1-7] can be selected in place of this parameter with proper
terminal block inputs. Refer to charts on Pages 5-29 and
5-30.
Important: If an adapter that is not connected is selected
as the active frequency source, the drive will fault on “Hz
Sel Fault” (F30).
Units Text Settings ‘‘Remote Pot”
‘‘0-10 Volt”
‘‘4-20 mA”
‘‘MOP”
‘‘Adapter 1”
‘‘Adapter 2”
‘‘Adapter 3”
‘‘Adapter 4”
‘‘Adapter 5”
‘‘Adapter 6”
‘‘Preset 1”
‘‘Preset 2”
‘‘Preset 3”
‘‘Preset 4”
‘‘Preset 5’’
‘‘Preset 6”
‘‘Preset 7”
[
F
re
q S
e
l
e
c
t
2
]
Parameter # 6 Factory Default ‘‘Remote Pot”
[
F
re
q S
e
l
e
c
t
2
]
Parameter Type Read & Write
This parameter controls which of the frequency sources is
currently supplying the [Freq Command] to the drive
unless [Freq Select 1] or [Preset Freq 1-7] are selected
with proper terminal block inputs. Refer to charts on Pages
5-29 and 5-30.
Important: If an adapter that is not connected is selected
as the active frequency source, the drive will fault on “Hz
Sel Fault” (F30).
Units Text Settings ‘‘Remote Pot”
‘‘0-10 Volt”
‘‘4-20 mA”
‘‘MOP”
‘‘Adapter 1”
‘‘Adapter 2”
‘‘Adapter 3”
‘‘Adapter 4”
‘‘Adapter 5”
‘‘Adapter 6”
‘‘Preset 1”
‘‘Preset 2”
‘‘Preset 3”
‘‘Preset 4”
‘‘Preset 5’’
‘‘Preset 6”
‘‘Preset 7”
- 1305 Adjustable 1
- Frequency AC Drive 1
- (Series C) 1
- PLEASE READ! 2
- IMPORTANT USER INFORMATION 2
- Summary of Changes 3
- SUMMARY OF DRIVE ENHANCEMENTS 4
- Table of Contents 7
- Appendix D – CE Conformity 8
- GENERAL PRECAUTIONS 10
- NAMEPLATE LOCATION 12
- 1305-BA03A-HAP SER C 12
- FIRMWARE COMPATIBILITY 12
- 1305 – A02 AA 13
- Information and Precautions 14
- Installation/Wiring 15
- TERMINAL BLOCK ACCESS 17
- INPUT DEVICES 19
- INPUT POWER CONDITIONING 20
- INPUT FUSING 20
- RFI FILTERING 22
- POWER WIRING 25
- P-P insulation design 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- User Side 34
- OUTPUT DEVICES 36
- CABLE TERMINATION 36
- ADAPTERS 37
- HIM DESCRIPTION 39
- HIM OPERATION 39
- Human Interface Module 40
- OFF Steady ON 41
- Steady ON OFF 41
- Flashing Steady ON 41
- Steady ON Flashing 41
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- OPERATOR LEVEL 44
- MODE LEVEL 44
- GROUP LEVEL 44
- PARAMETER LEVEL 44
- PROGRAM AND DISPLAY MODES 45
- Accel Time 46
- 99.9 Secs 46
- Choose Group 46
- Adapter 4 47
- X1111111 47
- PROCESS MODE 48
- Choose Mode 49
- Process Text 1 49
- EEPROM MODE 50
- EEPROM MODE (continued) 51
- CONTROL STATUS MODE 54
- PASSWORD MODE 56
- PASSWORD MODE (continued) 57
- Start-Up 60
- DESCRIPTION 61
- HIM DISPLAY 61
- Bul. 1305 Drive 62
- Connection Fail 62
- Open Enable Signal 65
- Restore Enable Signal 65
- Remove ALL Power 67
- Reconnect Motor 67
- Slowly Increase Speed 69
- PROGRAMMING EXAMPLE 73
- Metering Group (continued) 75
- 5-2 & 5-3 77
- Setup Group (continued) 78
- Figure 5.10 Start/Run Boost 88
- Figure 5.12 Analog Invert 90
- Two times 97
- [Skip Freq Band] 97
- Programming 100
- (continued) 100
- Figure 5.16 S-Curve 102
- Figure 5.17 S-Curve Time 103
- [( )])( )( 104
- Faults Group (continued) 109
- Diagnostics Group (continued) 112
- Masks Group (continued) 117
- Owners Group (continued) 120
- CHAPTER OBJECTIVES 126
- FAULT INFORMATION 126
- (continued) 129
- Appendix 138
- Table A.1 Specifications 139
- Serial Communications 144
- LOGIC CONTROL DATA 145
- DRIVE STATUS DATA 145
- SCALE FACTOR CONVERSION 145
- 25% of DRV 149
- 20% of DRC 149
- Drive Accessories 160
- ➀ Input reactor only 161
- CE Conformity 162
- ELECTRICAL CONFIGURATION 164
- GROUNDING 164
- CUT ALONG DOTTED LINE 170
Produits connexes et manuels pour Lecteurs de codes-barres Allen-Bradley 2-D
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels