Allen-Bradley 2-D Manuel d'installation

Naviguer en ligne ou télécharger Manuel d'installation pour Lecteurs de codes-barres Allen-Bradley 2-D. Allen-Bradley 2-D Installation manual [en] [es] [fr] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 22
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
APPLICATION NOTE:
INTEGRATING SERIES C&D MOTORS
WITH
ALLEN-BRADLEY ULTRA 3000i DRIVES
AN-0130 Rev B
Date: August 6, 2009
Model Numbers with LCB Option
40202C 40204C 40206C
40202D 40204D 40206D
50202C 50204C 50206C
50202D 50204D 50206D
Moog Components Group
Springfield Operations
750 West Sproul Road
Springfield, PA 19064
Ph: 610-328-4000, Toll Free: 800-510-6855
Fx: 610-605-6216 2009
E-mail: [email protected] Web-site: www.moog.com/components
Vue de la page 0
1 2 3 4 5 6 ... 21 22

Résumé du contenu

Page 1 - APPLICATION NOTE:

APPLICATION NOTE: INTEGRATING SERIES C&D MOTORS WITH ALLEN-BRADLEY ULTRA 3000i DRIVES AN-0130 Rev B Date: August 6, 2009 Model Numbers w

Page 2

4.1.2. High Response “D” System (IP-2D) Components: Component Part Number 1. Motor (one of): 50202DxxT-LCB-CV 50204DxxT-LCB-CV 50206D

Page 3 - Table of Contents:

4.2.2. Installing Ultraware: Installing Ultraware is very similar to installing most standard software. Follow the Allen-Bradley installation instruc

Page 4

Figure 4.4 Interconnections of IP-2C / IP-2D systems. AN-0130

Page 5 - 1 Safety:

4.4.1. Power Cable Termination Factory supplied motor power cables (MPC-30-25-3 for “C” series systems or MPC-60-25-3 for “D” series systems) are de

Page 6

4.4.3.1. Pendant Connection: The Control Pendant is wired to a 44-pin connector for CN1 no additional connection is needed on the pendant. 4.4.3.2

Page 7 - 3. Scope:

5. Creating Basic Motion with the System: After the system has been connected per section 4 and all the relevant Allen-Bradley instructions contain

Page 8

7. The system will again give an information message stating that presets are ignored. Select OK . 8. The system will begin to search for a

Page 9

5.1.3. Inserting Moog Motor Parameters: Power up the drive and Establish communications between the host computer and the Allen-Bradley drive in acco

Page 10

NOTE: When the load is attached the shaft moving mass will need to be changed to the total mass of the shaft plus load. 5.2. Setting In

Page 11 - 4.2.2. Installing Ultraware:

5.3.1. Description of Pendant: 1. Disable/Enable: In the Disable position the system is disabled from moving electronically by the drive. When pu

Page 12

PAGE INTENTIONALLY LEFT BLANK

Page 13 - 4.4.3. I/O Connections:

6. Tuning System: The tuning parameters entered in Section 5.3 are basic parameters used to create motion that is not necessarily precise. The system

Page 14 - 4.4.5. System AC Power

Appendix-A: (Revision History) ECO # Revision Change Date 0130 A Initial Rel

Page 15

AN-0130

Page 16 - 3k MOOG-Demo

Table of Contents: 1. SAFETY:...

Page 17

AN-0130 3 of 22

Page 18

AN-0130 4 of 22

Page 19

AN-0130 5 of 22

Page 21

4. Equipment and Interconnections: This section describes the equipment and interconnections in the Standard Response C and High Response D Series s

Page 22

4.1. Moog Integration Packages The Moog Integration Packages IP-2C and IP-2D are all-inclusive packages consisting of an Allen Bradley Ultra 3000i

Commentaires sur ces manuels

Viktor 14 May 2024 | 15:54:21

Hello!